GROHE BAULOOP single-lever bath&shower mixer with lockable diverter MODEL # 29041000

We want to ensure that you get long-lasting satisfaction and pleasure from your
GROHE fitting.
Do not use any abrasive sponges or scouring agents for cleaning. We also
advise you not to use cleaning agents containing solvent or acid, limescale
removers, household vinegar and cleaning agents with acetic acid in them. They
are aggressive to the surface – and will leave your fitting dull and scratched. As
the formulations of commercially available cleaning agents frequently change,
we cannot guarantee they will provide the gentle care our fitting deserves.
Clean the fitting with a little soap and a moist cloth only, then simply rinse off and
wipe dry. You can avoid lime spots by drying the fitting each time it is used. If
lime deposits do occur, remove them with GrohClean, our environment-friendly
cleaning liquid. GrohClean is specially formulated to clean the surface of our
fittings gently. GrohClean is available from your supplier.

Application
Can be used in conjunction with:
• Pressurised storage heaters
• Thermally controlled instantaneous heaters
• Hydraulically controlled instantaneous heaters
Operation with unpressurised storage heaters (= open water
heaters) is not possible.
Technical data
• Flow pressure
– min. 0.5 bar
– recommended by 29 041, 29 042 1 – 5 bar
– recommended by 29 062 1 – 5 bar
diverter automatically 0.7 – 5 bar
diverter seccured manually < 0.7 bar
• Operating pressure max. 10 bar
• Test pressure 16 bar
A pressure reducing valve must be fitted in the supply line if
static pressures exceed 5 bar to satisfy noise level ratings.
Avoid major pressure differences between hot and cold water
supply.
• Temperature
Hot water inlet: max. 80 °C
Recommended (energy saving): 60 °C
• Water connection hot – left
cold – right
Note:
This fitting can be combined with head and hand shower sets
by using a 3-way diverter.
Important note:
Never install shut-off valves in the outlet pipe (mixed
water) downstream of any built-in mixer.
Installation
Prepare the wall for the installation.
• Prepare the holes for the single lever mixer and slots for the
pipes.
Align single lever mixer using fitting template and fit.
• Permissible tolerances are given on the dimensional
drawing.
• The arrow on the fitting template must point upwards.
• To align place a spirit level on the fitting template.
• The housing is provided with pre-drilled holes (B) to facilitate
mounting the fitting to the wall.
• The finished surface of the wall (C) must lie within the
area (X) of the fitting template.
• The cold water supply must be connected on the right, hot
water supply on the left.
Connect pipes.
Open cold and hot-water supply and check connections
for water-tightness.
Flush piping system prior and after installation of fitting
thoroughly
Plaster and tile the wall.
Attention! You must tile directly to the fitting template!
Do not remove the fitting template before final installation.
Final installation
Remove fitting template.
Install escutcheon and lever.
Seal the escutcheon with silicone.
Check mixer for correct operation.
Function of automatic diverter (D) for 29 041.
Pulling the lever will release water delivery.
On the bath mixer, water will always emerge from the lower
outlet first (e.g. bath outlet).
Pressing diverter (D) shuts off the flow of water to the bath and
delivers water to the shower outlet.
When the mixer is closed, the diverter is released
automatically so that when the mixer is opened again, water
will always emerge from the lower outlet first (e.g. bath outlet).
Function of manual diverter (E) for 29 062.
Pulling the lever will release water delivery.
On the bath mixer, water will always emerge from the lower
outlet first (e.g. bath outlet).
Pressing diverter (E) shuts off the flow of water to the bath and
delivers water to the shower outlet.
In addition, the diverter assembly can be secured manually
(advantageous at pressures below 0.7 bar or at low rates of
discharge). In this case, press the diverter knob of the diverter
assembly (E) and turn it clockwise.
The diverter leave in this oposition until turning anti-clockwise.